Introduction
Clinically, atlantoaxial dislocation can be divided into reducible, irreducible and bony irreducible types according to the degree of difficulty in reduction [
1,
2]. For reducible dislocation, the focus of treatment is anatomical reduction, reliable fixation and fusion. Both the traditional Magerl screw fixation technique [
3] and the current Goel-Harms screw-rod fixation technique [
4,
5] can achieve this goal. For bony irreducible dislocation, since there is bony fusion between the atlas and axis during dislocation, reduction can only be achieved after complete osteotomy of all bony fusion sites, which is technically demanding during surgery, so the focus of treatment is decompression rather than reduction [
6]; For irreducible dislocation, due to scar tissue formation between C1–C2 which causes great resistance to reduction, reduction cannot be achieved by traction under anesthesia and the limited reduction forces provided by current screw-rod systems, so release of scar tissue between C1–2 by anterior or posterior approach is often required first to decrease the resistance before reduction can be achieved using plate or screw-rod systems [
7,
8]. However, the release also prolongs surgical time and increases surgical difficulty and risks.
Therefore, we designed a posterior reduction forceps for atlantoaxial dislocation (patent number: ZL201821593350.3) based on C1–2 posterior screw-rod system fixation, in order to overcome the resistance to reduction by the forceps without the need for release, aiming to greatly decrease surgical difficulty. The preliminary clinical application of this technique has achieved satisfactory results, which are reported as follows.
Discussion
For irreducible atlantoaxial dislocation, satisfactory reduction cannot be obtained simply relying on traditional internal fixation instruments. Although wire fixation techniques have some reduction capability, the reduction forces are insufficient to overcome scar tissue resistance in irreducible dislocations. The rigidity is also poor in all directions [
9]. The Magerl transarticular screw technique has good 3-dimensional rigidity [
10,
11] but cannot provide reduction forces and requires reduction to be achieved before screw placement. The C1–2 posterior screw-rod system [
12‐
14] has some reduction capability, and separate screw placement in C1 and C2 is convenient. But its limited reduction forces are still insufficient to overcome the resistance in irreducible dislocations, so satisfactory reduction cannot be obtained in some cases with simple screw-rod fixation. Therefore, the focus has been on how to achieve release to decrease the resistance to reduction. Release can be achieved by anterior transoral approach directly, followed by reduction and plate fixation [
15], or posterior screw-rod fixation [
7]. Transoral release, reduction and fixation through single approach has the advantage of achieving release, reduction, fixation, decompression and fusion [
16]. But it is a type II wound with higher infection risks compared to type I posterior wound. Therefore more surgeons prefer transoral release first, followed by posterior screw-rod fixation. However, intraoperative position change is complex after release when C1–2 is extremely unstable, posing risks of spinal cord injury [
17]. For anterior release, some chose transmandibular approach or minimally invasive tubular access for release before posterior reduction and fixation to decrease infection risks and trauma [
18,
19]. But the exposure and release are limited compared to extensive transoral release. Position change is still required. To avoid position change, some achieved release through simple posterior approach by opening C1–2 facet joints followed by screw-rod reduction and fixation [
20]. However, the posterior venous plexus around the C1–2 joints poses difficulties in exposure and hemostasis. Also, variations like the vertebral artery entering spinal canal below C1 posterior arch can lead to vertebral artery injuries during release. Only the facet joints can be released through posterior approach. In summary, currently existing release techniques before reduction and fixation all have some limitations—higher infection risks for transoral approach; limited exposure and release for minimally invasive anterior release; risk of bleeding and vertebral artery injuries for posterior release; and the need for intraoperative position change for anterior followed by posterior approach. If reduction can be obtained without release, surgical difficulty can be remarkably decreased by avoiding release, reducing surgical time and blood loss.
For irreducible C1–2 dislocation, there is only soft tissue scar formation rather than bony fusion between the dislocated C1 and C2. So reduction without release is theoretically possible if sufficient reduction forces can be generated to overcome the resistance from scar tissue. However, the reduction forces provided by traditional screw-rod systems are insufficient. How can greater reduction forces be achieved? Our designed posterior reduction forceps for atlantoaxial dislocation uses C2 pedicle screw as the fulcrum to pull C1 screw and C1 by mechanical forces, providing additional external reduction forces for C1–2 reduction. As long as C1 screw does not get pulled out and C2 screw does not break during reduction, the scar tissue resistance can be overcome to achieve reduction without release. Our early clinical experience indicates that the forceps is easy to use during surgery, and the large reduction forces generated by rotating the screw can overcome scar tissue resistance. Satisfactory C1–2 reduction can be obtained without release in irreducible dislocations, remarkably decreasing the difficulty of surgery for such cases.
However, the design of the reduction forceps relies on fixation with C1 and C2 pedicle screws, so it cannot be used if pedicle screw placement in C1 and C2 is not feasible. For C1, the screw can be pedicle screw, partial pedicle screw, lateral mass screw or posterior arch hook, as long as the proximal end of the reduction arm can be attached. But C1 posterior arch screw cannot be used based on current C1 fixation techniques. For C2, the screw can be pedicle screw, pars screw, lateral mass screw or C2–3 transarticular screw, as long as the supporting arm can be clamped onto the screw head. This device is currently not suitable for the C2 laminar screw. Because the application of the posterior reduction forceps requires a fulcrum, and the force at this fulcrum is transmitted downwards. If the C2 laminar screw is used as the reduction fulcrum, the downward force may cause spinal cord compression, C2 laminar splitting, or fracture.
During surgery, pedicle screws satisfying the above criteria do not have to be placed bilaterally. Unilateral screw placement allowing use of the reduction forceps is sufficient to achieve reduction from one side, while the contralateral side just needs auxiliary fixation. Considering that the high riding VA cannot be treated with cervical pedicle screws as the reduction fulcrum, we propose the following solutions. If one side is high riding VA, the other side can be selected to apply posterior reduction forceps. If both sides are high riding VA, the option is to insert C2 pars screws or C3 pedicle screws as the reduction fulcrum. Cases with bilaterally unsuitable screw placement are extremely rare. Therefore, the reduction forceps can be applied in most clinical scenarios. The reduction capability is limited by the maximal anti-breaking strength of C2 screw and the maximal anti-pullout strength of C1 screw. So the C2 screw needs to withstand bending forces and the C1 screw needs high anti-pullout strength. In severe osteoporosis cases, screw augmentation with bone cement and improved screw design can enhance screw anti-pullout and anti-breaking capabilities to meet surgical reduction requirements. These will be important aspects for future research.
Our early results suggest that satisfactory C1–2 reduction can be obtained without release using the designed forceps and traditional screw-rod system, even with only unilateral forceps application. This indicates that the reduction capability of the forceps is powerful and may eliminate the need for release, remarkably decreasing surgical risks and difficulty in irreducible atlantoaxial dislocation. However, the case number is still limited and further application is needed to summarize the outcomes.
Publisher's Note
Springer Nature remains neutral with regard to jurisdictional claims in published maps and institutional affiliations.